Sharp AR-235 Operation Manual Download | Manualshive

Page: 134 / 158

background image

KEY OPERATOR PROGRAMS

132

K

EY OP

ER

A

T

OR

’S GU

ID
E

Preheat Mode

Preheat mode functions to reduce the power consumption by lowering the temperature of the fusing
unit to a programmed level once a programmed length of time has elapsed without any copier operation
after the last copy of a run is made or power is turned on. The preheat mode will help lower the user's
electricity bill, reduce waste of natural resources, and cut down on environmental pollution. The
programmed time is set to the factory default of 15 minutes as shipped from the factory. The default
time can be changed optionally within the prescribed range of time. We suggest you set the most
appropriate time according to your usage pattern.
The interval can be set to 1, 2, 5, 10, 15, 30, 60, 120 or 240 minutes.
When "PREHEAT MODE" is selected and the OK key is pressed, the following display will appear.

1.

Select the desired time interval using the and keys.

2.

Press the OK key.

Message Time

This program is used to adjust the length of time that messages are displayed. The message time can
be set to 3, 6 or 9 seconds. The factory setting is 6 seconds.
When "MESSAGE TIME" is selected and the OK key is pressed, the following display will appear.

1.

Select the time using the and keys.

2.

Press the OK key.

PREHEAT MODE

15

min.

(1~240)

MESSAGE TIME

SHORT (3sec.)

NORMAL(6sec.)

LONG (9sec.)

00EX.book 132 ページ２００１年５月２５日金曜日午前１０時４９分

«
...
132
133
134
135
136
...
»

Summary of Contents for AR-235































































































































































Reviews:

No comments

Related manuals for AR-235

Copycentre C118

Brand: Xerox Pages: 230

Brand: Olivetti Pages: 50

Brand: Olivetti Pages: 90

Brand: Xerox Pages: 9

Brand: Canon Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands