Sharp AR-235 Operation Manual Download

Page: 109 / 158

FINISHER (AR-FN5)

107

AL E

UIP

Use the and keys to select "STAPLE SORT" and press the OK key.

●

Also the OUTPUT key can be used to select an output mode.

Set the number of copies and press the START (

) key.

Replace the scanned original with the next original and press the
START (

) key after it lights up. Repeat this step until all originals

have been scanned.

After all originals have been scanned, press the READ-END key.

●

Copying will start and each set of completed copies will be automatically stapled and
delivered to the offset tray.

●

If the message "Can not continue. Remove paper from the offset tray." appears in the
display, remove the copies from the offset tray.

00EX.book 107 ページ２００１年５月２５日金曜日午前１０時４９分

Summary of Contents for AR-235































































































































































Search results

Summary of Contents for AR-235

Reviews:

Related manuals for AR-235

Brands by name

Popular brands

Sharp AR-235, Operation Manual

Search results

Summary of Contents for AR-235

Reviews:

Related manuals for AR-235

Brands by name

Popular brands