Sharp AR-235 Operation Manual Download

Page: 102 / 158

SINGLE PASS FEEDER (AR-SP4)/REVERSING SINGLE PASS FEEDER (AR-RP3)

100

AL E

UIP

Use the and keys to select two-sided to one-sided copying.

Use the or key to select binding change if desired. Then, press the
OK key.

●

The image of one side can be rotated 180º using the image rotation feature. This feature
can be useful depending on the orientation of the original image and the desired binding
position.

Set the number of copies and press the START (

) key.

●

Press the CLEAR (C) key to stop copying in the middle of a run.

●

Be sure not to touch the originals as they move on the reversing tray. This may cause
misfeeds.

COPY MODE

1 to 2

to 2

2 to 1

BINDING CHANGE

OFF

00EX.book 100 ページ２００１年５月２５日金曜日午前１０時４９分

Summary of Contents for AR-235































































































































































Search results

Summary of Contents for AR-235

Reviews:

Related manuals for AR-235

Brands by name

Popular brands

Sharp AR-235, Operation Manual

Search results

Summary of Contents for AR-235

Reviews:

Related manuals for AR-235

Brands by name

Popular brands