Sharp AR-235 Operation Manual Download

Page: 49 / 158

IAL FUNCTIONS

ERASE

This copier has an edge erase mode and a centre erase mode.

●

Edge erase can be used to eliminate shadow lines around the edges of copies which appear when
thick paper or a book is used as an original.

●

Centre erase can be used to eliminate the shadow produced by the bindings of bound documents.

●

Edge + centre erase can be used together to eliminate both types of shadow lines.

●

The standard erase width is 10 mm (1/2"), but can be changed from 5 mm to 20 mm in 5 mm
increments (from 1/4" to 1" in 1/4" increments).

★

KEY OPERATOR

The initial setting of the width for edge erase and centre erase can be changed.

See page 127.

●

This feature cannot be used with the 2 in 1 or 4 in 1 feature.

●

If the dual page copy feature has been set, centre erase and edge + centre erase cannot be set.

●

This feature cannot be used with non-standard size originals.

Place an original on the platen glass or in the document feeder tray.

Press the SPECIAL FUNCTION key. Then press the OK key.

●

The SPECIAL MODES screen will appear.

Use the and keys to select "ERASE" and press the OK key.

●

The setting screen for ERASE will appear.

A B

Centre erase

Edge + Centre erase

Edge erase

Document feeder tray

SPECIAL MODES

MARGIN SHIFT

ERASE

DUAL PAGE COPY

[OK]:ADJUST

ERASE

-----

OFF

EDGE

CENTRE

mm(5~20)

00EX.book 47 ページ２００１年５月２５日金曜日午前１０時４９分

Summary of Contents for AR-235































































































































































Search results

Summary of Contents for AR-235

Reviews:

Related manuals for AR-235

Brands by name

Popular brands

Sharp AR-235, Operation Manual

Search results

Summary of Contents for AR-235

Reviews:

Related manuals for AR-235

Brands by name

Popular brands