Sharp AR-235 Operation Manual Download

Page: 85 / 158

TONER CARTRIDGE REPLACEMENT

NE
R

L INFORMATION

Remove the new toner cartridge from the bag. Grasp the cartridge on
both sides and shake it horizontally approximately 20 times. After
shaking the cartridge, remove the tape.

NOTE:

Grasp the grip when holding the cartridge. Do not hold the cartridge by the shutter. Be sure to
only shake the cartridge before the tape is removed.

Gently insert the toner cartridge along the guides until it clicks in
place while pushing the lock release lever.

NOTE:

If dirt or dust is adhered to the toner cartridge, remove it before installing the cartridge.

Remove the tape from the shutter. Pull the shutter out of the toner
cartridge as shown in the illustration. Discard the shutter.

Close the front cover.

Shutter

Tape

Approx. 20 times

00EX.book 83 ページ２００１年５月２５日金曜日午前１０時４９分

Summary of Contents for AR-235































































































































































Search results

Summary of Contents for AR-235

Reviews:

Related manuals for AR-235

Brands by name

Popular brands

Sharp AR-235, Operation Manual

Search results

Summary of Contents for AR-235

Reviews:

Related manuals for AR-235

Brands by name

Popular brands