Sharp AR-235 Operation Manual Download

Page: 99 / 158

SINGLE PASS FEEDER (AR-SP4)/REVERSING SINGLE PASS FEEDER (AR-RP3)

AL E

UIP

Press the 2-SIDED COPY key.

●

The duplex copy mode selection screen will appear.

Use the and keys to select one-sided to two-sided copying.

●

Also the 2-SIDED COPY key can be used to select a duplex copy mode.

Use the or key to select binding change if desired. Then, press
the OK key.

●

The image of one side can be rotated 180º using the image rotation feature. This feature
can be useful depending on the orientation of the original image and the desired binding
position.

Set the number of copies and press the START (

) key.

●

Press the CLEAR (C) key to stop copying in the middle of a run.

COPY MODE

1 to 1

1 to 2
2 to 2

COPY MODE

1 to 1

1 to 2

2 to 2

BINDING CHANGE

OFF

00EX.book 97 ページ２００１年５月２５日金曜日午前１０時４９分

Summary of Contents for AR-235































































































































































Search results

Summary of Contents for AR-235

Reviews:

Related manuals for AR-235

Brands by name

Popular brands

Sharp AR-235, Operation Manual

Search results

Summary of Contents for AR-235

Reviews:

Related manuals for AR-235

Brands by name

Popular brands