Sharp AR-235 Operation Manual Download

Page: 103 / 158

SINGLE PASS FEEDER (AR-SP4)/REVERSING SINGLE PASS FEEDER (AR-RP3)

101

AL E

UIP

Misfeed removal

If an original misfeed occurs in the SPF or RSPF, the copier will stop and the message "Clear paper
path." will appear.

Remove the misfed originals.

Location A

Open the feeding roller cover and pull the misfed original gently to the left and out from
the document feeder tray. Close the feeding roller cover.

Location B

Open the document feeder cover, rotate the rollers in the direction indicated by the
arrow to feed the misfed paper, and then gently remove the misfed original after closing
the document feeder cover.

Feeding roller cover

Rollers

00EX.book 101 ページ２００１年５月２５日金曜日午前１０時４９分

Summary of Contents for AR-235































































































































































Search results

Summary of Contents for AR-235

Reviews:

Related manuals for AR-235

Brands by name

Popular brands

Sharp AR-235, Operation Manual

Search results

Summary of Contents for AR-235

Reviews:

Related manuals for AR-235

Brands by name

Popular brands