Sharp AR-235 Operation Manual Download

Page: 54 / 158

2 IN 1 OR 4 IN 1

IAL FUNCTIONS

Press the SPECIAL FUNCTION key. Then press the OK key.

●

The SPECIAL MODES screen will appear.

Use the and keys to select "2in1/4in1" and press the OK key.

●

The selection screen for 2 in 1 / 4 in 1 will appear.

Use the and keys to select "2in1" or "4in1" and press the OK key.

●

The setting screen for 2 in 1 or 4 in 1 will appear.

Use the and keys to select the desired layout pattern.

●

Select the order of originals which will be arranged on the copies. For layout patterns,
see the previous page.

SPECIAL MODES

MARGIN SHIFT

ERASE

DUAL PAGE COPY

[OK]:ADJUST

2in1/4in1

-----

OFF

2in1

4in1

[OK]:CHANGE

PATTERN 1

BORDER

2in1

00EX.book 52 ページ２００１年５月２５日金曜日午前１０時４９分

Summary of Contents for AR-235































































































































































Search results

Summary of Contents for AR-235

Reviews:

Related manuals for AR-235

Brands by name

Popular brands

Sharp AR-235, Operation Manual

Search results

Summary of Contents for AR-235

Reviews:

Related manuals for AR-235

Brands by name

Popular brands