Sharp AR-235 Operation Manual Download | Manualshive

Page: 36 / 158

background image

REDUCTION/ENLARGEMENT/ZOOM

34

MA

KING COP

IE

S

4

Press the OK key.

●

The display will return to the basic screen.

5

Ensure that the desired paper tray is selected.

●

If the auto paper select function has been enabled, the appropriate copy paper size will
have been automatically selected based on the original size and the selected copy ratio.

●

If the auto paper select function has been disabled or if copying onto a different size
paper, use the PAPER SELECT key to select the paper feed station with the desired
paper size.

6

Set the number of copies and press the START (

) key.

00EX.book 34 ページ２００１年５月２５日金曜日午前１０時４９分

«
...
34
35
36
37
38
...
»

Summary of Contents for AR-235































































































































































Reviews:

No comments

Related manuals for AR-235

Brand: Toshiba Pages: 9

Brand: Toshiba Pages: 48

Brand: Toshiba Pages: 78

Brand: Toshiba Pages: 84

Brand: Toshiba Pages: 75

Brand: Toshiba Pages: 84

Brand: Toshiba Pages: 95

Brand: Toshiba Pages: 124

Brand: Toshiba Pages: 130

Brand: Toshiba Pages: 150

Brand: Toshiba Pages: 171

Brand: Toshiba Pages: 166

Brand: Toshiba Pages: 180

Brand: Toshiba Pages: 190

Brand: Toshiba Pages: 238

Brand: Toshiba Pages: 239

Brand: Toshiba Pages: 257

Brand: Toshiba Pages: 264

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands