Sharp AR-235 Operation Manual Download

Page: 110 / 158

FINISHER (AR-FN5)

108

AL E

UIP

Using the SPF or the RSPF

Set the originals in the document feeder tray.

●

If the number of copies in one set is more than 30, the copies will not be stapled.

●

If the orientation of the originals does not match that of the copy paper, the images of the
originals will be rotated. The stapling position varies with the orientation of the original.

●

When copying B4 (8-1/2" x 14") or A3 (11" x 17") size originals with portrait orientation
images, copies will be stapled at the position shown below.

Press the OUTPUT key.

●

The output mode selection screen will appear.

Use the and keys to select "STAPLE SORT" and press the OK key.

●

Also the OUTPUT key can be used to select an output mode.

Stapling position

OUTPUT

NO SORT

SORT

STAPLE SORT

EXIT

CENTER

CENTRE

00EX.book 108 ページ２００１年５月２５日金曜日午前１０時４９分

Summary of Contents for AR-235































































































































































Search results

Summary of Contents for AR-235

Reviews:

Related manuals for AR-235

Brands by name

Popular brands

Sharp AR-235, Operation Manual

Search results

Summary of Contents for AR-235

Reviews:

Related manuals for AR-235

Brands by name

Popular brands