Sharp AR-235 Operation Manual Download

Page: 53 / 158

IAL FUNCTIONS

2 IN 1 OR 4 IN 1

The 2 in 1 or 4 in 1 feature is used to copy 2 or 4 originals, collectively in a specified order, onto one
sheet.

●

These features cannot be used with the dual page copying, XY zoom, erase or margin shift features.

●

Copies can be made with or without the border lines.

●

The order of originals which will be arranged on the copies can be selected. There are two patterns of
layout for 2 in 1 copying and four patterns of layout for 4 in 1 copying.

●

Non-standard size paper cannot be used with the 2 in 1 or 4 in 1 feature.

●

If this feature is set, the copy ratio will be automatically set and cannot be changed manually.

●

The 2 in 1 or 4 in 1 feature cannot be set for interrupt copying. While 2 in 1 or 4 in 1 is being set,
interrupt will not function.

Place an original on the platen glass or in the document feeder tray.

Use the PAPER SELECT key to select the paper tray with the desired
paper size.

4 in 1 copying

2 in 1 copying

Pattern

Document feeder tray

00EX.book 51 ページ２００１年５月２５日金曜日午前１０時４９分

Summary of Contents for AR-235































































































































































Search results

Summary of Contents for AR-235

Reviews:

Related manuals for AR-235

Brands by name

Popular brands

Sharp AR-235, Operation Manual

Search results

Summary of Contents for AR-235

Reviews:

Related manuals for AR-235

Brands by name

Popular brands