Sharp AR-235 Operation Manual Download

Page: 117 / 158

500-SHEET PAPER FEED UNIT (AR-D11)/2x500-SHEET PAPER FEED UNIT (AR-D12)

115

AL E

UIP

Loading copy paper

The method of loading copy paper for these paper feed units is the same as for the paper trays in the
copier. See page 78.

Changing the copy paper size in the tray

The method of changing the copy paper size is the same as for the paper trays in the copier. See page
80.

Misfeed removal

The copier will stop when a misfeed occurs. The message "Clear paper path." will appear along with a
display of paper misfeed locations.

Open the side cover of the paper tray which was in use and remove
the misfed paper.

●

Be sure to perform this step before pulling out the paper trays. If not, the paper may be
torn as the trays are opened.

00EX.book 115 ページ２００１年５月２５日金曜日午前１０時４９分

Summary of Contents for AR-235































































































































































Search results

Summary of Contents for AR-235

Reviews:

Related manuals for AR-235

Brands by name

Popular brands

Sharp AR-235, Operation Manual

Search results

Summary of Contents for AR-235

Reviews:

Related manuals for AR-235

Brands by name

Popular brands