Sharp AR-235 Operation Manual Download | Manualshive

Page: 132 / 158

background image

KEY OPERATOR PROGRAMS

130

K

EY OP

ER

A

T

OR

’S GU

ID
E

1.

Use the or key to enable or disable the offset function for the
centre tray of the copier.

2.

If a finisher is installed, use the key to select "OFFSET TRAY" and
use the or key to enable or disable the offset function for the offset
tray of the finisher.

3.

Press the OK key.

Memory for Printer

This copier has a memory for storing data of scanned originals. If a printer expansion kit is installed,
part of this memory will be used for storing print data. This program is used to set the percentage of the
memory used for the printer feature. The default setting is 50%.
When "MEMORY FOR PRINTER" is selected and the OK key is pressed, the following display will
appear.

1.

Use the and keys to select the desired percentage.

2.

Press the OK key.

NOTE:

The memory capacity for storing original images and print data is 16 MB. The memory can be
extended to a maximum of 272 MB by adding commercially available memory modules.

Toner Save Mode

The toner save mode will reduce toner consumption by approximately 10% in the automatic, text, and
text/photo exposure modes. Copies will be lighter but still adequate for general use. Selection of this
mode has no effect on the photo and super photo modes.

To turn on the toner save mode, highlight "TONER SAVE MODE" and press
the OK key to display a check mark in the check box.

To turn off the toner save mode, select this program and press the OK key
again to clear the check mark in the check box.

MEM. FOR PRINTER

30%
40%

50%

60%

00EX.book 130 ページ２００１年５月２５日金曜日午前１０時４９分

«
...
130
131
132
133
134
...
»

Summary of Contents for AR-235































































































































































Reviews:

No comments

Related manuals for AR-235

Brand: Panasonic Pages: 342

Brand: Olivetti Pages: 61

Brand: Canon Pages: 394

Copycentre C118

Brand: Xerox Pages: 2

C123 Copycentre

Brand: Xerox Pages: 2

imageRUNNER 1600

Brand: Canon Pages: 4

Brand: Utax Pages: 296

Brand: Ricoh Pages: 284

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands