Sharp AR-235 Operation Manual Download | Manualshive

Page: 97 / 158

background image

SINGLE PASS FEEDER (AR-SP4)/REVERSING SINGLE PASS FEEDER (AR-RP3)

95

6

OP

T

IO

N

AL E

Q

UIP

M

E

N

T

Using the SPF or the RSPF

★

KEY OPERATOR

If SPF/RSPF is disabled using a key operator program, the SPF or the RSPF

cannot be used. See page 135.

One-sided copies from one-sided originals

1

Ensure that no original is left on the platen glass.

2

Adjust the original guides to the size of the originals.

3

Set the originals face up in the document feeder tray.

●

The original size will be indicated in the display, and the paper tray with the
corresponding paper size will be automatically selected.

★

KEY OPERATOR

The auto paper select function can be disabled using a key operator

program. If this function has been disabled, use the PAPER SELECT key to select the
desired paper tray. See page 134.

●

To copy onto a different size paper, use the PAPER SELECT key to make the selection.

Stream feeding mode

If the stream feeding mode has been enabled using a key operator program, the message "Set
originals for stream feeding." will appear for approximately 5 seconds after feeding of all originals is
completed. While this message is displayed, any new originals placed in the SPF or RSPF will be fed
and copied automatically.

★

KEY OPERATOR

See page 128 for information on setting the stream feeding mode.

00EX.book 95 ページ２００１年５月２５日金曜日午前１０時４９分

«
...
95
96
97
98
99
...
»

Summary of Contents for AR-235































































































































































Reviews:

No comments

Related manuals for AR-235

Brand: Oce Pages: 220

Brand: Oki Pages: 32

Brand: Gestetner Pages: 168

Brand: Ricoh Pages: 371

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands