Sharp AR-235 Operation Manual Download | Manualshive

Page: 33 / 158

background image

31

2

MA

KING COP

IE

S

REDUCTION/
ENLARGEMENT/ZOOM

Reduction and enlargement ratios can be selected either automatically with the AUTO IMAGE key or
manually with the COPY RATIO key. The zoom function enables precise copy ratio selection from 25%
to 400% in 1% increments.

●

The allowable copy ratio range is limited to the following conditions:

Automatic selection

●

When the auto image function is enabled, the reduction or enlargement ratio cannot be selected
manually.

1

Place an original on the platen glass and close the platen cover.

●

The original size will be automatically detected and indicated in the display. If the original
is a non-standard size, it cannot be detected. In this case, press the SPECIAL
FUNCTION key to enter the original size. See page 24.

2

Use the PAPER SELECT key to select the paper tray with the desired
paper size.

●

This feature will not work when copy paper of non-standard size is used.

Exposure mode

Location of original

Copy ratio range

Other than SUPER PHOTO

SPF/RSPF (optional)

50% to 200%

SUPER PHOTO

Platen glass

50% to 200%

SUPER PHOTO

SPF/RSPF (optional)

50% to 141%

00EX.book 31 ページ２００１年５月２５日金曜日午前１０時４９分

«
...
31
32
33
34
35
...
»

Summary of Contents for AR-235































































































































































Reviews:

No comments

Related manuals for AR-235

Brand: Panasonic Pages: 92

Brand: Panasonic Pages: 187

Brand: Panasonic Pages: 270

Brand: Xerox Pages: 22

Brand: Ricoh Pages: 97

Brand: Ricoh Pages: 676

Brand: Oce Pages: 381

Brand: Olivetti Pages: 22

Brand: Olivetti Pages: 332

Brand: Xerox Pages: 4

Brand: Xerox Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands