Sharp AR-235 Operation Manual Download | Manualshive

Page: 64 / 158

background image

JOB MEMORY

62

S

P

E

C

IAL FUNCTIONS

4

Select a program number from 1 to 9 using the numeric keys.

●

A screen indicating that the settings have been stored will appear and then the display
will return to the basic screen.

●

The numbers with a check mark are program numbers which already contain job
programs. If a program number containing a job program is entered, the message
"Storage number selected is already used. Replace it?" will appear to confirm the
selection. To replace an existing program with the new program, select "YES" with the
and keys and press the OK key.

●

If the existing program is not to be replaced, select "NO" with the and keys, press the
OK key, and select another register number.

Deleting a job program

1

Press the PROGRAM key.

●

The JOB PROGRAMS screen will appear.

2

Use the and keys to select "DELETE" and press the OK key.

●

The DELETE JOB PROGRAM screen will appear.

●

To cancel the job memory mode, press the BACK key or the CLEAR ALL (CA) key.

JOB PROGRAMS

RECALL

STORE

DELETE

DELETE JOB PROGRAM

1

2

3

4

5

6

7

8

9

[10-key]:SELECT

00EX.book 62 ページ２００１年５月２５日金曜日午前１０時４９分

«
...
62
63
64
65
66
...
»

Summary of Contents for AR-235































































































































































Reviews:

No comments

Related manuals for AR-235

Brand: Oce Pages: 389

Brand: Sharp Pages: 5

AR-C330 Key operators

Brand: Sharp Pages: 5

Brand: Sharp Pages: 20

Brand: Sharp Pages: 22

Brand: Sharp Pages: 22

Brand: Sharp Pages: 22

Brand: Sharp Pages: 16

Brand: Sharp Pages: 18

Brand: Sharp Pages: 19

Brand: Sharp Pages: 30

Brand: Sharp Pages: 32

Brand: Sharp Pages: 26

Brand: Sharp Pages: 19

Brand: Sharp Pages: 19

Brand: Sharp Pages: 36

Brand: Sharp Pages: 25

AR-DE9 (1 TRAY UNIT)

Brand: Sharp Pages: 47

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands