Sharp AR-235 Operation Manual Download | Manualshive

Page: 84 / 158

background image

82

GE

NE
R

A

L INFORMATION

TONER CARTRIDGE
REPLACEMENT

The approximate quantity of toner remaining can be displayed by pressing and holding the COPY key
during standby or warm-up. See page 84. When the quantity of toner remaining is less than 25%,
obtain a new cartridge. When the toner cartridge replacement required icon ( ) appears in the display,
replacement of the toner cartridge will be needed soon. If you press the information key, the message
"Toner is low." will appear in the display. When the message "Add toner. Can not copy or print."
appears in the display, the toner cartridge must be replaced before copying can be resumed. Replace
the toner cartridge by following the procedure below.

NOTE:

During a long copy run of a dark original, the message "Toner replenishment in progress." may
appear, even though there is toner remaining and the copier will suspend the copying job whilst it
replenishes its toner supply. This can take up to 2 minutes after which the START (

) key

indicator will light up. Press the START (

) key to resume copying.

1

Gently open the front cover.

2

Push the toner cartridge lock release lever and pull the toner cartridge
out. Remove the toner cartridge while supporting it with the left hand
at the green label portion.

●

For disposal of the old toner cartridge, contact your dealer.

NOTE:

After removing the toner cartridge, do not shake it or tap on it. Doing so may cause toner to leak
from the cartridge. Put the old cartridge immediately in the bag contained in the box of the new
cartridge.

For best copying results, be sure to use only SHARP products. The
package of SHARP toner has the Genuine Supplies label.

GENUINE SUPPLIES

Toner cartridge
lock release lever

Grip

00EX.book 82 ページ２００１年５月２５日金曜日午前１０時４９分

«
...
82
83
84
85
86
...
»

Summary of Contents for AR-235































































































































































Reviews:

No comments

Related manuals for AR-235

DCP 385C - Color Inkjet - All-in-One

Brand: Brother Pages: 256

DCP 385C - Color Inkjet - All-in-One

Brand: Brother Pages: 529

Brand: Ricon Pages: 32

Document Centre 50

Brand: Xerox Pages: 284

Brand: Canon Pages: 5

Brand: Canon Pages: 393

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands