Sharp AR-235 Operation Manual Download

Page: 81 / 158

PAPER

NE
R

L INFORMATION

Move the left guide to the appropriate slot as marked on the tray.

●

When using 11" x 17" copy paper, store the left guide in the slot at the left front of the
paper tray.

Fan the copy paper and insert it into the tray.

●

Set the paper along the guides.

●

The tray holds up to 500 sheets of 80

(21 lb.) paper.

●

Do not load paper above the maximum height line.

Push the paper tray firmly back into the copier.

●

If the paper size is changed in steps 3 and 4, place the paper size card in the front of the
paper tray to indicate the selected paper size. Proceed to the next section.

Maximum height line

Paper size
card

EXTRA

x13

Paper size
card

EXTRA

x14

x11

x13

11x1 7

00EX.book 79 ページ２００１年５月２５日金曜日午前１０時４９分

Summary of Contents for AR-235































































































































































Search results

Summary of Contents for AR-235

Reviews:

Related manuals for AR-235

Brands by name

Popular brands

Sharp AR-235, Operation Manual

Search results

Summary of Contents for AR-235

Reviews:

Related manuals for AR-235

Brands by name

Popular brands