Sharp AR-235 Operation Manual Download | Manualshive

Page: 130 / 158

background image

KEY OPERATOR PROGRAMS

128

K

EY OP

ER

A

T

OR

’S GU

ID
E

To establish new initial settings
1.

Use the and keys to select "NEW DEFAULT" and press the OK key.

2.

Use the and keys to select an item of which the initial setting is to
be changed and press the OK key.

●

Use the and keys if needed.

3.

Use the and keys to select the desired setting and press the OK
key.

4.

Repeat steps 2 and 3 until all desired settings have been made.

●

The settings for number of copies, XY zoom, auto image function, interrupt, special
functions, output tray in the sort, gourp or staple sort mode, and display contrast cannot
be set by this procedure.

5.

Press the BACK key repeatedly to exit the program.

●

A paper tray can be selected as the default tray. The auto paper select mode, however,
cannot be cancelled.

●

A duplex copy mode can be set as the default mode. If "2-sided copy" is disabled using a
key operator program (page 135), 1-sided to 2-sided and 2-sided to 2-sided will be reset
to 1-sided to 1-sided. If the RSPF is disabled using a key operator program (page 135),
2-sided to 2-sided and 2-sided to 1-sided will be reset to 1-sided to 1-sided.

To return to the factory default settings
1.

Use the and keys to select "FACTORY DEFAULT" and press the
OK key.

2.

Use the and keys to select "YES" and press the OK key.

Stream Feeding

This program is used to enable the stream feeding mode of an SPF or RSPF. When the stream feeding
mode is enabled, additional originals which are set in the document feeder tray within 5 seconds after
the previous original was fed will be fed and copied automatically.

To enable the stream feeding mode, highlight "STREAM FEEDING" and
press the OK key to display a check mark in the check box.

To disable this function, select this program and press the OK key again to
clear the check mark in the check box.

Rotation Copy

If this program is set, the image of originals will rotate when the orientation of the originals does not
match that of the copy paper.
Rotation copy will function only when the auto paper select or auto image mode has been selected.

NOTE:

If the image is rotated in reduction copying, the position of the image in relation to copy paper will
vary with the orientations of the originals and copy paper.

Original

Copy paper

Copy

00EX.book 128 ページ２００１年５月２５日金曜日午前１０時４９分

«
...
128
129
130
131
132
...
»

Summary of Contents for AR-235































































































































































Reviews:

No comments

Related manuals for AR-235

Brand: Panasonic Pages: 342

DocuColor DocuColor 4

Brand: Xerox Pages: 20

WorkCentre Pro 65

Brand: Xerox Pages: 150

WorkCentre Pro 423

Brand: Xerox Pages: 4

Brand: Xerox Pages: 144

Brand: Xerox Pages: 114

Brand: Olivetti Pages: 604

Brand: Olivetti Pages: 110

Brand: Canon Pages: 174

Brand: Canon Pages: 965

Brand: Gestetner Pages: 168

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands