Sharp AR-235 Operation Manual Download

Page: 78 / 158

TROUBLESHOOTING

COP

TROUBLE

CAUTION:

Be sure to use only genuine SHARP parts and supplies.

Please contact your SHARP service centre immediately if a problem persists after checking the above.

Problem

Solution

Copies are smudged or
dirty.

●

Platen glass or platen cover
dirty?

Clean regularly. See page 84.

●

Original smudged or blotchy?

Use a clean original.

Black or white stripes
appear on copies.

●

Is the scanning window of an
optional SPF or RSPF dirty?

Clean the scanning window.

Paper size for a paper tray
cannot be set.

●

Is the COPY indicator off?

Press the COPY key to select the
COPY mode. See page 14.

●

Is copying, printing or facsimile
printing being performed?

Set the paper size after copying,
printing or facsimile printing is
complete.

Power is on but copying is
not possible.

●

Are only the mode indicators on? The copier is in the auto power

shut-off mode. Press the COPY key
or another mode key that is lit.

●

Is the COPY indicator off?

Press the COPY key to select the
COPY mode.

●

Is two-sided printing being
performed?

Wait until the printing job finishes.

Lighting fixture flickers.

●

Is the same power outlet used for
the lighting fixture and the
copier?

Connect the copier to a power
outlet which is not used for other
electric appliances.

00EX.book 76 ページ２００１年５月２５日金曜日午前１０時４９分

Summary of Contents for AR-235































































































































































Search results

Summary of Contents for AR-235

Reviews:

Related manuals for AR-235

Brands by name

Popular brands

Sharp AR-235, Operation Manual

Search results

Summary of Contents for AR-235

Reviews:

Related manuals for AR-235

Brands by name

Popular brands