Sharp AR-235 Operation Manual Download | Manualshive

Page: 138 / 158

background image

KEY OPERATOR PROGRAMS

136

K

EY OP

ER

A

T

OR

’S GU

ID
E

Disable Auto Power Shut-off

The auto power shut-off mode is used to turn off the power to the fuser automatically once a
programmed length of time has elapsed without any copier operation after the last copy of a run is
made or power is turned on. This mode lowers the user's electricity bill, reduces waste of natural
resources, and cuts down on environmental pollution.
Depending on how the machine is to be used, you may wish for some reasons to disable this mode.
This can be done using this program.

NOTE:

Since we would like you to fully understand the purpose of this mode, we suggest that you
enable this mode and set the most appropriate time using program "AUTO POWER OFF" (page
131).

To disable the auto power shut-off mode, highlight "DISABLE AUTO
POWER SHUT-OFF" and press the OK key to display a check mark in the
check box.

To restore the mode, select this program and press the OK key again to
clear the check mark in the check box.

Disable Beep at Key Touch

This program is used to enable or disable the beep function. If this function is enabled, a beep sound
will be produced when you press a key on the operation panel.

To disable the beep function, highlight "DISABLE BEEP AT KEY TOUCH"
and press the OK key to display a check mark in the check box.

To enable the beep function, select this program and press the OK key
again to clear the check mark in the check box.

Disable Backlight Change

With the factory default setting, the display colour varies with the copier status as shown below:

Green: Normal
Yellow: Toner is low or maintenance will be needed soon
Orange: The copier cannot operate because of a misfeed, no toner or some other malfunction.

This program is used to disable the function that changes backlighting colour.

To disable change of the backlight colour, highlight "DISABLE
BACKLIGHT CHANGE" and press the OK key to display a check mark in
the check box.

To enable the function, select this program and press the OK key again to
clear the check mark in the check box.

00EX.book 136 ページ２００１年５月２５日金曜日午前１０時４９分

«
...
136
137
138
139
140
...
»

Summary of Contents for AR-235































































































































































Reviews:

No comments

Related manuals for AR-235

Brand: Panasonic Pages: 92

Brand: Panasonic Pages: 187

Document Centre 240

Brand: Xerox Pages: 322

Image Reader-A1

Brand: Canon Pages: 916

Copy Centre 518

Brand: Xerox Pages: 2

Brand: U-Reach Pages: 17

Brand: FFEI Pages: 162

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands