Sanyo MCO-19M, Service Manual

Page: 37 / 187

- 34 -
㻌
㻌
㻌
<CO2 span calibration>
㻌
㻌
䣖 䣧 䣯 䣲 䢱 䣅 䣑 䢴 䢱 䣑 䢴 䣅 䣣 䣮 䣫 䣤 䣴 䣣 䣶 䣫 䣱 䣰 䢪 䢳 䢱 䢴 䢫
䣒 䣘 䣘 䣱 䣮 䣶
䣖 䣧 䣯 䣲 䣕 䣲 䣣 䣰 䢲 䢰 䢲 䤑䣅 䢵 䢹 䢰 䢲 䤑䣅 䢲 䢰 䢷 䤑䣅
䣅 䣑 䢴 䣜 䣧 䣴 䣱 䢵 䢰 䢻 䢳 䣘 䢷 䢲 䢲
䣅 䣑 䢴 䣕 䣲 䣣 䣰 䢲 䢰 䢲 䢧 䢷 䢰 䢲 䢧 䢵 䢰 䢳 䢸 䣘 䢹 䢲 䢲
䣑 䢴 䣜 䣧 䣴 䣱 䢷 䢲 䢲
䣑 䢴 䣕 䣲 䣣 䣰 䢲 䢰 䢲 䢧 䢷 䢰 䢲 䢧 䢷 䢺 䣯 䣘 䢷 䢲 䢲
㻌
㻌
1. In Top Screen, press MENU key and select “Tools”.
2. Press ENTER key to display “Select Tools (1/2)” and select “Temp/CO2/O2 Calibration”.
3. Press ENTER key to display “Temp/CO2/O2 Calibration (1/2)”.
4. Input a CO2 measured value in the right side of “CO2 Span”.
5. Press MENU key and select “OK”.
6. Press ENTER key to start CO2 calibration automatically.
㻌 㻌 㻌 Perform CO2 calibration until display CO2 density corresponds to actual CO2 density.
Note) It is impossible to perform CO2 span calibration when setting CO2 density is 0.0
䠂
There is a blank in the right side of “CO2 Span” column.
Ex.
䠅 When CO2 density setting is 5.0% and actual CO2 density is 4.5%;
Procedures MENU key
0 Measure CO2 density by sampling port in the front of inner door.
1 In Top Screen, press MENU key and select “Tools”. Tools
2 Press ENTER key to display “Select Tools (1/2)” and select “Temp/CO2/O2 Calibration”.
3 Press MENU key and select “OK”. OK
4 Press ENTER key to display “Temp/CO2/O2 (1/2)”. Input “4.5” in the right side of “CO2
Span” column.
5 Press MENU key and select “OK”. OK
6 Press ENTER key to return the display to “Select Tools (1/2)”.
㻌
䣖 䣧 䣯 䣲 䢱 䣅 䣑 䢴 䢱 䣑 䢴 䣅 䣣 䣮 䣫 䣤 䣴 䣣 䣶 䣫 䣱 䣰 䢪 䢳 䢱 䢴 䢫
䣒 䣘 䣘 䣱 䣮 䣶
䣖 䣧 䣯 䣲 䣕 䣲 䣣 䣰 䢲 䢰 䢲 䣅 䢵 䢹 䢰 䢲 䣅 䢲 䢰 䢷 䣅
䣅 䣑 䢴 䣜 䣧 䣴 䣱 䢵 䢰 䢻 䢳 䣘 䢷 䢲 䢲
䣅 䣑 䢴 䣕 䣲 䣣 䣰 䢲 䢰 䢲 䢧 䢷 䢰 䢲 䢧 䢵 䢰 䢳 䢸 䣘 䢹 䢲 䢲
䣑 䢴 䣜 䣧 䣴 䣱 䢷 䢲 䢲
䣑 䢴 䣕 䣲 䣣 䣰 䢲 䢰 䢲 䢧 䢷 䢰 䢲 䢧 䢷 䢺 䣯 䣘 䢷 䢲 䢲