Sanyo MCO-19M, Service Manual

Page: 30 / 187

- 27 -
䣑 䣍
䣷 䣵 䣕 䣶 䣣 䣶
䣖 䣱 䣱 䣮 䣵
䢲 䢷 䢰 䢲 䢰 䢹 䢵
䣎 䣱 䣩
䣕 䣧 䣶
䣇 䣐 䣗
䣅 䣑 䢴 䤑䣅 䣖 䣧 䣯 䣑 䢴
䣏
䢷 䢰 䢲 䢧 䣲 䢵 䢹 䢰 䢲
㻌
㻌
㻌
㻌 3. MENU/Set - Various settings
㻌
㻌
䣑 䣍
䣷 䣵 䣕 䣶 䣣 䣶
䣖 䣱 䣱 䣮 䣵
䢲 䢷 䢰 䢲 䢰 䢹 䢵
䣎 䣱 䣩
䣕 䣧 䣶
䣇 䣐 䣗
䣅 䣑 䢴 䤑䣅 䣖 䣧 䣯 䣑 䢴
䣏
䢷 䢰 䢲 䢧 䣲 䢵 䢹 䢰 䢲
㻌
㻌
㻌
䣕 䣶 䣣 䣰 䣦 䢯 䣤 䣻 䣕 䣧 䣶 䣶 䣫 䣰 䣩
䣖 䣧 䣯 䣲 䣧 䣴 䣣 䣶 䣷 䣴 䣧 䢵 䢹 䢰 䢲 䤑䣅 䢪 䢲 䢰 䢲 䤑 䣅 䢯 䢷 䢲 䢰 䢲 䤑䣅 䢫
䣅 䣑 䢴 䣆 䣧 䣰 䣵 䣫 䣶 䣻 䢷 䢰 䢲 䢧 䢪 䢲 䢰 䢲 䢧 䢯 䢴 䢲 䢰 䢲 䢧 䢫
䣑 䢴 䣆 䣧 䣰 䣵 䣫 䣶 䣻 䢷 䢰 䢲 䢧 䢪 䢳 䢰 䢲 䢧 䢯 䢳 䢺 䢰 䢲 䢧 䢫
䢪 䢴 䢴 䢰 䢲 䢧 䢯 䢺 䢲 䢰 䢲 䢧 䢫
䣍 䣧 䣻 䣎 䣱 䣥 䣭 䢲 䢪 䢲 䢰 䣗 䣰 䣮 䣱 䣥 䣭 䢳 䢰 䣎 䣱 䣥 䣭 䢫
䣊 䣫 䣩 䣪 䣎 䣫 䣯 䣫 䣶 䢷 䢴 䢰 䢲 䤑䣅
㻌
<Setting of chamber temperature>
In Top Screen, press MENU key and select Set.
Press ENTER key to display current setting temperature in the right side of “Temperature “ column
in “Stand-by Setting” display.
Input required value and press MENU key and select OK in reverse video.
Press ENTER key to memorize the input value.
Setting range is 0 ~ 50.0
䉝 .
Note) Maximum 50.0 䉝 for settable value. Error tone is not emit if you input a value over 50.0 䉝 .
<Setting of CO2 density>
In Top Screen, press MENU key and select Set.
Press ENTER key to display current setting CO2 density in the right side of “CO2 Density” column
In “Stand-by Setting” display.
Input required value and press MENU key and select OK in reverse video.
Press ENTER key to memorize the input value.
Setting range is 0 ~ 20.0%.
Note) Maximum 20.0% for settable value. Error tone is not emit if you input a value over 20.0%.
<Setting of O2 density>
In Top Screen, press MENU key and select Set.
Press ENTER key to display current setting O2 density in the right side of “O2 Density” column
In “Stand-by Setting” display.
Input required value and press MENU key and select OK in reverse video.
Press ENTER key to memorize the input value.
Setting range is 1~80.0%. (Controllable range: 1~18.0%, 22.0%~80.0%)
Note) O2 is set to 1.0% when you input a value lower than 1.0% and is set to 80.0% when you input a value
over 80.0%. Error tone is not emit.
Note) Press ENTER key with “Cancel” displayed in reverse video to cancel the setting change.
<Display of high limit setting temperature>
High limit setting temperature is displayed in the right side of “High Limit” column in “Stand-by Setting” display.
Setting range is 35
䉝
~51
䉝
.
When a chamber temperature is over high limit setting temperature, LED illuminates and audible alarm sounds
continuously. (The audible alarm will not stop sounding if BUZZER key is pressed)