Rigol DL3000 Series User Manual Download Page 33

Page: 33 / 163

Chapter 2 Front Panel Operations

RIGOL

DL3000 User’s Guide

2-3

Static Operation Mode

The static operation modes include the following 4 modes:



Constant Current (CC) Mode



Constant Voltage (CV) Mode



Constant Resistance (CR) Mode



Constant Power (CP) Mode

Constant Current (CC) Mode

In CC mode, the electronic load will sink a current in accordance with the

programmed value regardless of the input voltage, as shown in Figure 2-1.

Figure 2-1 Constant Current (CC) Mode

Operation Procedures:

Power on the instrument
Press the Power key

on the front panel to power on the instrument.

Connect the DUT and the channel input terminals of the load

Connect the DUT and the channel input terminals on the front panel of the load

as shown in Figure 2-2.

Figure 2-2 Connect to the Terminals

Load Current

Set Current

Input Voltage

Front Panel

DUT

Summary of Contents for DL3000 Series




































































































































































Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands

Rigol DL3000 Series, User Manual

Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands