Rigol DL3000 Series User Manual Download Page 98

Page: 98 / 163

RIGOL

Chapter 2 Front Panel Operations

2-68

DL3000 User’s Guide

Set Fail_Tip

If the test is failed, you can determine whether to display the prompt message

that indicates the test failure.

(1)

In the main interface, press Fail_Tip to switch the parameter focus to

"Fail_Tip".

(2)

Press Fail_Tip to enable or disable the display of the prompt message. You

can also use the Left/Right arrow key or the knob to switch the on/off state.

Set Pass_Sound

If the test is passed, you can determine whether to sound the alarm for test

pass.

(1)

In the main interface, press Pass_Sound to switch the parameter focus to

"Pass_Sound".

(2)

Press Pass_Sound to enable or disable the alarm sound once the test is

passed. You can also use the Left/Right arrow key or the knob to switch the

on/off state.

Set Fail_Sound

If the test is failed, you can determine whether to sound the alarm for test

failure.

(1)

In the main interface, press Fail_Sound to switch the parameter focus to

"Fail_Sound".

(2)

Press Fail_Sound to enable or disable the alarm sound once the test is

failed. You can also use the Left/Right arrow key or the knob to switch the

on/off state.

Turn on the channel input

Press On/Off to turn on the channel input for the factory test function. At this
time, the actual input voltage, current, resistance, and power will be displayed in

the main interface.

WARNING

To avoid electric shock, ensure that the DUT is connected to the

input terminals of the load properly before you turn on the channel

input.

CAUTION

When the fan stops working, the channel is disabled. Then, a

message is displayed, "Fan stops running!"

Exit the factory test function

Press any key on the front panel of the load to exit the factory test function.

Summary of Contents for DL3000 Series




































































































































































Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands

Rigol DL3000 Series, User Manual

Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands