Rigol DL3000 Series User Manual Download Page 132

Page: 132 / 163

RIGOL

Chapter 2 Front Panel Operations

2-102

DL3000 User’s Guide

(3)

ManualIP (manual configuration)

In this mode, you can self-define the network parameters (such as the IP

address) of the instrument. Press ManualIP to enable or disable the

manual IP configuration mode. By default, it is "OFF".

If you enable this mode, "IP Address", "SubMask", "Gateway", and "DNS" at the

right section of the interface can be editable.

Tip

If you set "ManualIP" to be "ON", then "DHCP" and "AutoIP" will both be

automatically set to "OFF"; if you set "ManualIP" to be "OFF", then "DHCP" and

"AutoIP" will both be automatically be set to "ON".



Set IP Address

In the manual IP mode, you need to acquire an available IP address from

the administrator, and then configure the IP address manually. The format

of the IP address is "nnn.nnn.nnn.nnn". The range for the first segment

(nnn) of the address is from 1 to 223 (except 127); and the range for the

other three segments is from 0 to 255.

In the manual IP mode, press the Up/Down arrow key to switch the

parameter focus to "IP Address", and then press the Left/Right arrow key to

move the cursor. Use the numeric keys or the knob to input the IP address.

The setting is saved to the non-volatile memory. If "Power-on" is set to

"Last", and the next you power on the instrument, set both "DHCP" and

"AutoIP" to "OFF", in this case, the instrument will automatically load the

set IP address.



Set the subnet mask

In the manual IP mode, you need to acquire an available subnet mask from

the administrator, and then configure the subnet mask manually. The

format of the subnet mask is "nnn.nnn.nnn.nnn". The range for the first

segment (nnn) is from 0 to 255.

In the manual IP mode, press the Up/Down arrow key to switch the

parameter focus to "SubMask", and then press the Left/Right arrow key to

move the cursor. Use the numeric keys or the knob to input the subnet

mask.

The setting is saved to the non-volatile memory. If "Power-on" is set to

"Last", and the next you power on the instrument, set both "DHCP" and

"AutoIP" to "OFF", in this case, the instrument will automatically load the

set subnet mask.

Summary of Contents for DL3000 Series




































































































































































Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands

Rigol DL3000 Series, User Manual

Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands