Rigol DL3000 Series User Manual Download Page 133

Page: 133 / 163

Chapter 2 Front Panel Operations

RIGOL

DL3000 User’s Guide

2-103



Set the default gateway

In the manual IP mode, you need to acquire an available gateway address

from the administrator, and then configure the default gateway manually.

The format of the default gateway is "nnn.nnn.nnn.nnn". The range for the

first segment (nnn) of the address is from 1 to 223 (except 127); and the

range for the other three segments is from 0 to 255.

In the manual IP mode, press the Up/Down arrow key to switch the

parameter focus to "Gateway", and then press the Left/Right arrow key to

move the cursor. Use the numeric keys or the knob to input the gateway

address.

The setting is saved to the non-volatile memory. If "Power-on" is set to

"Last", and the next you power on the instrument, set both "DHCP" and

"AutoIP" to "OFF", in this case, the instrument will automatically load the

set gateway address.



Set DNS

In the manual IP mode, you need to acquire an available DNS address from

the administrator, and then configure the DNS address manually. The

format of the DNS address is "nnn.nnn.nnn.nnn". The range for the first

segment (nnn) of the address is from 1 to 223 (except 127); and the range

for the other three segments is from 0 to 255.

In the manual IP mode, press the Up/Down arrow key to switch the

parameter focus to "DNS", and then press the Left/Right arrow key to move

the cursor. Use the numeric keys or the knob (fine-tune) to input the DNS

address.

The setting is saved to the non-volatile memory. If "Power-on" is set to

"Last", and the next you power on the instrument, set both "DHCP" and

"AutoIP" to "OFF", in this case, the instrument will automatically load the

set DNS address.

Physical Address

Physical address is also called media access control address (MAC address). It is

also called hardware address, which can be used to define the location of the

network device. The physical address for one device is unique and is not allowed

Tip

If the input subnet mask is invalid, a prompt message "Invalid subnet

mask. The subnet mask must be contiguous." will be displayed.

Tip

The three IP configuration modes cannot be all set to "ON" or "OFF".

Summary of Contents for DL3000 Series




































































































































































Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands

Rigol DL3000 Series, User Manual

Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands