Rigol DL3000 Series User Manual Download Page 147

Page: 147 / 163

Chapter 3 Remote Control

RIGOL

DL3000 User’s Guide

3-5

Remote Control via LAN

Connect the load to the PC

Use the network cable to connect the load to the PC or the local area network

(LAN) where the PC resides.

Configure network parameters

DHCP mode:

If the network supports DHCP, the DHCP server in the network assigns

network parameters (IP Address, Subnet Mask, Gateway and DNS) for the

load automatically.

Auto IP mode:

The load will automatically select the auto IP mode when any of the

following three conditions occur: 1) the network doesn’t support DHCP; 2)

DHCP mode of the load is disabled; 3) the load is connected to the PC

directly. After selecting the auto IP mode, it will acquire the IP address

ranging from "169.254.0.1" to "169.254.255.254" and subnet mask

255.255.0.0 automatically.

Manual IP mode:

Enable the Manual IP mode and disable the DHCP mode as well as the Auto

IP mode to set the network parameters manually.

If the load is connected to the PC directly, set the IP Addresses, Subnet

Masks and Gateways for both of the PC and the load. The Subnet Masks and

Gateways of the load and PC must be the same and their IP Addresses must

be within the same network segment (for details, refer to the TCP/IP

protocol). An example is shown in the table below.

Network

Parameters

Load

IP Address

Subnet mask

Default gateway

192.16.3.3

255.255.255.0

192.16.3.1

192.16.3.8

255.255.255.0

192.16.3.1

If the load is connected to the local network area where the PC resides,

please acquire a set of valid network parameters from the administrator and

configure the network parameters of the load according to the descriptions

in "Set the parameters for the LAN interface".

Search for the device resource
Start Ultra Sigma, and then click

. A window is displayed as shown in

Figure (a). Click

and the software searches for the instrument

resource currently connected to the PC or the LAN where the PC resides. The

Summary of Contents for DL3000 Series




































































































































































Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands

Rigol DL3000 Series, User Manual

Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands