Rigol DL3000 Series User Manual Download Page 131

Page: 131 / 163

Chapter 2 Front Panel Operations

RIGOL

DL3000 User’s Guide

2-101

Connection status

The status of the load will be displayed based on the current network connection

status.



Connected: indicates that the network has been successfully connected.



Disconnected: indicates that the network is disconnected or network

connection has failed.



Configuring Network...: indicates that the network is being configured.



IP Assignment Failed: indicates being failed to obtain the IP address.



IP Conflict: indicates that the IP address is conflicted with that of other

systems on the network.

IP Configuration

There are three types of IP configuration modes:



DHCP (Dynamic Host Configuration Protocol)



AutoIP (automatic configuration)



ManualIP (manual configuration)

In different IP configuration modes, the configurations for IP address and other

network parameters are different.

(1)

DHCP (Dynamic Host Configuration Protocol)

In this mode, the DHCP server on the current network assigns network

parameters (such as the IP address) to the instrument. Press DHCP to

enable or disable the DHCP configuration mode. By default, it is "ON".

(2)

AutoIP (automatic configuration)

In this mode, the instrument acquires the IP address ranging from

"169.254.0.1" to "169.254.255.254" and the subnet mask (255.255.0.0)

automatically according to the current network configuration. Press

AutoIP to enable or disable the auto IP configuration mode. By default, it

is "ON".

Tip

If the current network connection status is displayed as "Disconnected", then

the IP configuration shows "No Configure".

The three IP configuration modes cannot be all set to "ON" or "OFF".

Tip

When DHCP and AutoIP are turned on at the same time, the instrument takes

DHCP as the priority. Therefore, if you need to enable the AutoIP mode,

please set DHCP to "OFF" first.

Summary of Contents for DL3000 Series




































































































































































Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands

Rigol DL3000 Series, User Manual

Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands