Rigol DL3000 Series User Manual Download Page 18

Page: 18 / 163

RIGOL

Chapter 1 Quick Start

1-6

DL3000 User’s Guide



System Info

Displays the manufacturer, device model, software and

hardware versions, FPGA version, boot version, system boot

times, calibration date, and product serial number.



Reset

Restores the instrument settings to its factory default

settings, For default settings, refer to Table 2-3.

(3)

Advanced function key

Provides advanced functions. Currently, the factory test function

and CC+CV function are supported.

(4)

Storing and recalling operation key

Saves, reads, deletes, copies, and pastes the files. The

instrument provides an internal non-volatile memory ("Disk C")

and supports an external memory ("Disk D"). A maximum of 100

files can be stored in the instrument.

(5)

Help key

Enters the built-in help system. You can view relevant help

information for any key or menu key on the front panel.

Knob

(1)

Switch the parameters or parameter values.

(2)

Increases (rotate clockwise) or decreases (rotate counterclockwise) the

value at the cursor.

Note: Rotating the knob in different interfaces can produce different operation

results. Here introduces its common usage. For other specific usages and

operation methods, refer to details in relevant chapters.

Input Control Keys

(1)

Input on/off key

Enables or disables the sink function of the load.

(2)

Transient trigger key

Turns on or off the transient trigger function.

(3)

Short-circuit key

Enables or disables the short circuit function of the load.

Summary of Contents for DL3000 Series




































































































































































Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands

Rigol DL3000 Series, User Manual

Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands