Rigol DL3000 Series User Manual Download Page 93

Page: 93 / 163

Chapter 2 Front Panel Operations

RIGOL

DL3000 User’s Guide

2-63

"T_Stop".

(2)

Press T_Stop to switch to "ON", and select the discharge time to be

the termination condition.

(3)

Enter a value by using the numeric keys, arrow keys, or the knob. For

the setting methods, refer to the descriptions of the built-in help

information or refer to the descriptions in "Parameter Setting

Method".



If you do not need to set the discharge time to be the termination

condition:

(1)

In the main interface, press T_Stop to switch the parameter focus to

"T_Stop".

(2)

Press T_Stop to switch to "OFF", and the input box is disabled, and

you are unable to input any value.

Set Von

When the input voltage is greater than the set starting voltage (Von), the load

starts to sink the current. The default unit for Von is V, and it ranges from 0 V to

150 V. The default Von is 0.5 V. To enable or disable this function, refer to

descriptions in "Enable/Disable the Von Latch Function".

(1)

In the main interface, press Von to switch the parameter focus to "Von".

(2)

Enter a value by using the numeric keys, arrow keys, or the knob. For

setting methods, refer to the descriptions of the help information or refer to

the descriptions in "Parameter Setting Method".

Turn on the channel input
Press On/Off to turn on the channel input

At this time, the actual current,

discharge voltage, current discharge time, discharged capacitance, and battery

energy will be displayed in the main interface.

If the termination condition for the battery discharge is met, after completing

the test, a prompt message is displayed, "Battery test completed!" Press OK to

exit.

Note: Once the channel input is turned on, the load will not start to sink the

current until the input voltage is greater than the starting voltage.

WARNING

To avoid electric shock, ensure that the battery is connected to the

input terminals of the load properly before you turn on the channel

input.

View waveform display

Press the waveform display key

to enter the waveform display interface,

as shown in Figure 2-38. By default, it displays the current waveform. When you

select "I" under "Data", the battery is discharged in CC mode. For detailed

operation, refer to descriptions in "Waveform Display Function". Press the

Summary of Contents for DL3000 Series




































































































































































Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands

Rigol DL3000 Series, User Manual

Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands