Rigol DL3000 Series User Manual Download Page 134

Page: 134 / 163

RIGOL

Chapter 2 Front Panel Operations

2-104

DL3000 User’s Guide

to be modified. It can be used to identify the instrument when you assign the IP

address to the instrument. A physical address is a 48-bit (6-byte) addressing

scheme, usually represented in Hex. For example, 00-2A-A0-A5-E0-56.

VISA

VISA (Virtual Instrument Software Architecture), developed by NI (National

Instrument), provides an advanced programming interface to communicate with

various instruments through their bus lines. VISA enables you to communicate

with the instrument in the same way, without considering the interface type of

the instrument (such as GPIB, USB, LAN/Ethernet, or RS232). The instruments

that communicate with the PC via GPIB, USB, LAN/Ethernet, or RS232 are called

"Resources".

VISA indicates the resource name, which describes the name and location of the

resource. For example, when you use the LAN interface to communicate with

the instrument, the VISA descriptor is displayed as

"TCPIP::172.16.3.100::INSTR".

Apply

Press Apply, and then the currently set network parameters will take effect.

Note: After you configure the network parameters, you must press Apply to apply

the currently set network parameters, and then the new settings will take effect.

Summary of Contents for DL3000 Series




































































































































































Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands

Rigol DL3000 Series, User Manual

Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands