Rigol DL3000 Series User Manual Download Page 121

Page: 121 / 163

Chapter 2 Front Panel Operations

RIGOL

DL3000 User’s Guide

2-91

the load will enter its corresponding interface. (Note: The load will enter the

guide interface (if any) first.)

Delete

You can delete the files in Disk C and D, as well as the empty folders in Disk D.

Operation Procedures:

Press Store on the front panel of the load to enter the storage and recall

interface.

Press Cursor to switch to the directory, and select the directory where the file to

be deleted, and then press Cursor again to select the file to be deleted or select

the empty folder.

Press Delete, and then a prompt message "Delete the file?" is displayed. You

can press OK to delete the currently selected file or the empty folder; press

Cancel to give up deleting files or folders.

Copy and Paste

You are only allowed to copy the files from Disk C and paste them to Disk D.

Operation Procedures:

Press Store on the front panel of the load to enter the storage and recall

interface.

Press Cursor to switch to the directory and select Disk C, and then press
Cursor again to select the file to be copied.

Press Copy to copy the currently selected file.

Press Cursor to switch to the directory and select Disk D.

Press Paste to paste the copied file to Disk D. After you successfully completed

the copy and paste operation, a prompt message "Files copied successfully!" is

displayed.

If the same file is found in Disk D, a prompt message "Overwrite the existing

file?" is displayed. Press OK to overwrite the existing file; press Cancel to give

up the pasting operation.

Summary of Contents for DL3000 Series




































































































































































Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands

Rigol DL3000 Series, User Manual

Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands