Rigol DL3000 Series User Manual Download Page 32

Page: 32 / 163

RIGOL

Chapter 2 Front Panel Operations

2-2

DL3000 User’s Guide

Local/Remote Operation Mode

The load provides two operation modes: local and remote.

Local Operation Mode

After you power on the instrument, it enters the local operation mode by default. In

the local operation mode, all the keys on the front panel are available for you to use.

Remote Operation Mode

In the remote operation mode, you can send the programming commands from the

PC via any one of the interfaces (GPIB, USB, RS232, or LAN).

In remote operation mode, all the keys (except the Power key

and the Local

key) were disabled. You can only control the load by programming commands. To

return to the local operation mode, press Local on the front panel.

Tip

Factory test mode and APP functions (OCP/OPP) do not support remote operation.

Summary of Contents for DL3000 Series




































































































































































Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands

Rigol DL3000 Series, User Manual

Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands