Rigol DL3000 Series User Manual Download Page 30

Page: 30 / 163

RIGOL

Chapter 1 Quick Start

1-18

DL3000 User’s Guide

Parameter Setting Method

Most parameters can be set by operating the keys on the front panel. The common

setting methods are listed below. The setting method for certain parameters is

different from the methods below, refer to the relevant chapters of this manual for

the further explanation.

Method 1: Use the numeric keys

In the main interface, press the specified menu key to switch the parameter

focus; in the guide interface, use the arrow keys to switch the parameter focus.

Enter a value by using the numeric key. While entering a name, press

delete the unwanted character if necessary.

When setting resistance, press the specified menu key and select "Ω" or "kΩ" to

be the unit.

When setting period/width, press the specified menu key and select "ms" or "s"

to be the unit.

When setting frequency, press the specified menu key and select "Hz" or "kHz"

to be the unit.

When setting other parameters, press OK to confirm the input.

Method 2: Use the knob or the arrow keys

In the main interface, press the specified menu key to switch the parameter

focus.

Press the Left/Right arrow key to move the cursor to a desired position.

Press the Up/Down arrow key or rotate the knob to modify the value.

Summary of Contents for DL3000 Series




































































































































































Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands

Rigol DL3000 Series, User Manual

Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands