Rigol DL3000 Series User Manual Download Page 43

Page: 43 / 163

Chapter 2 Front Panel Operations

RIGOL

DL3000 User’s Guide

2-13

Set V_Limit

The upper limit of the voltage working in CR mode. The default unit for V_Limit

is V, and it ranges from 0 V to 155 V.

(1)

In the main interface, press V_Limit to switch the parameter focus to

"V_Limit".

(2)

Enter a value by using the numeric keys, arrow keys, or the knob. For

setting methods, refer to the descriptions of the help information or refer to

the descriptions in "Parameter Setting Method".

Set C_Limit

The upper limit of the current working in CR mode. The default unit for C_Limit

is A, and it ranges from 0 A to 70 A.

(1)

In the main interface, press C_Limit to switch the parameter focus to

"C_Limit".

(2)

Enter a value by using the numeric keys, arrow keys, or the knob. For setting

methods, refer to the descriptions of the help information or refer to the

descriptions in "Parameter Setting Method".

Set Von

When the input voltage is greater than the set starting voltage (Von), the load

starts to sink the current. The default unit for Von is V, and it ranges from 0 V to

155 V. The default Von is 0 V. To enable or disable this function, refer to

descriptions in "Enable/Disable the Von Latch Function".

(1)

In the main interface, press Von to switch the parameter focus to "Von".

(2)

Enter a value by using the numeric keys, arrow keys, or the knob. For

setting methods, refer to the descriptions of the help information or refer to

the descriptions in "Parameter Setting Method".

Turn on the channel input
Press On/Off to turn on the channel input

At this time, the actual input

voltage, current, resistance, and power will be displayed in the main interface.

Note: Once the channel input is turned on, the load will not start to sink the

current until the input voltage is greater than the starting voltage.

WARNING

To avoid electric shock, ensure that the DUT is connected to the

input terminals of the load properly before you turn on the channel

input.

CAUTION

When the fan stops working, the channel is disabled. Then, a

message is displayed, "Fan stops running!"

View waveform display

Press the waveform display key

to enter the waveform display interface,

Summary of Contents for DL3000 Series




































































































































































Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands

Rigol DL3000 Series, User Manual

Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands