Rigol DL3000 Series User Manual Download Page 162

Page: 162 / 163

RIGOL

Chapter 5 Appendix

5-4

DL3000 User’s Guide

Appendix B: Warranty

RIGOL

warrants that the product mainframe and product accessories will be free

from defects in materials and workmanship within the warranty period. If a product

proves defective within the warranty period,

RIGOL

guarantees free replacement or

repair for the defective product.

To get repair service, please contact with your nearest

RIGOL

sales or service office.

There is no other warranty, expressed or implied, except such as is expressly set

forth herein or other applicable warranty card. There is no implied warranty of

merchantability or fitness for a particular purpose. Under no circumstances shall

RIGOL

be liable for any consequential, indirect, ensuing, or special damages for any

breach of warranty in any case.

Summary of Contents for DL3000 Series




































































































































































Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands

Rigol DL3000 Series, User Manual

Search results

Summary of Contents for DL3000 Series

Reviews:

Related manuals for DL3000 Series

Brands by name

Popular brands