manualshive.com logo in svg

Renesas SH7705, Hardware Manual

The Renesas SH7705 user manual is a comprehensive hardware guide for this powerful product. Download it for free from manualshive.com to explore the device's features, functionalities, and technical specifications. This manual ensures a seamless user experience, enabling you to unlock the full potential of the Renesas SH7705.

Share
Download
background image

Rev. 2.00, 09/03, page 354 of 690

15.3.1

64-Hz Counter (R64CNT)

The 64-Hz counter (R64CNT) is an 8-bit read-only register that indicates the state of the divider
circuit between 64 Hz and 1 Hz.

R64CNT is reset to H'00 by setting the RESET bit in RCR2 or the ADJ bit in RCR2 to 1.

R64CNT is not initialized by a power-on reset or manual reset, or in standby mode.

Bit

Bit Name

Initial Value

R/W

Description

7

0

R

Reserved

This bit is always read as 0.

6 to 0

R

64-Hz Counter

Each bit (bits 6 to 0) indicates the state of the

RTC divider circuit between 64 Hz and 1 Hz.

Bit

Frequency

6:

1 Hz

5:

2 Hz

4:

4 Hz

3:

8 Hz

2:

16 Hz

1:

32 Hz

0:

64 Hz

15.3.2

Second Counter (RSECCNT)

The second counter (RSECCNT) is an 8-bit readable/writable register used for setting/counting in
the BCD-coded second section. The count operation is performed by a carry for each second of the
64-Hz counter.

The range of second that can be set is 00 to 59 (decimal). Errant operation will result if any other
value is set. Carry out write processing after stopping the count operation with the START bit in
RCR2.

RSECCNT is not initialized by a power-on reset or manual reset, or in standby mode.

Summary of Contents for SH7705




































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7705

3Com 3CRWB6096 Quick Start Manual preview
3CRWB6096
Brand: 3Com Pages: 8
EAW MX8600 Jumpstart Manual preview
MX8600
Brand: EAW Pages: 6
EAW UX8800 Technical Note preview
UX8800
Brand: EAW Pages: 6
National Instruments SCXI-1121 User Manual preview
SCXI-1121
Brand: National Instruments Pages: 162
PaloAlto Networks PA-7500 Quick Start Manual preview
PA-7500
Brand: PaloAlto Networks Pages: 3
Oracle Talari E1000 Installation Manual preview
Talari E1000
Brand: Oracle Pages: 24
Idis DR-8432 Installation Manual preview
DR-8432
Brand: Idis Pages: 31
FOR-A USF-105AS Operation Manual preview
USF-105AS
Brand: FOR-A Pages: 39
EKF Electronik CompactPCI CC8-BLUES User Manual preview
CompactPCI CC8-BLUES
Brand: EKF Electronik Pages: 52
Garland EdgeLens INT10G8LR56 User Manual preview
EdgeLens INT10G8LR56
Brand: Garland Pages: 30
u-blox ANT-B10 User Manual preview
ANT-B10
Brand: u-blox Pages: 29
Zhone IMACS Network Device Product Manual preview
IMACS Network Device
Brand: Zhone Pages: 114
Magma ExpressBox7 Quick Installation Manual preview
ExpressBox7
Brand: Magma Pages: 2
Cypress Semiconductor CY7C1350G Specification Sheet preview
CY7C1350G
Brand: Cypress Semiconductor Pages: 15
G&D DVI-Vision-IP-Fiber Installation And Operation Manual preview
DVI-Vision-IP-Fiber
Brand: G&D Pages: 240
Comtrend Corporation WAP-5922MP Quick Install Manual preview
WAP-5922MP
Brand: Comtrend Corporation Pages: 4
Xilinx MP3 NG Application Note preview
MP3 NG
Brand: Xilinx Pages: 27
Vivint AirBridge VS-YOFIMN-000 Quick Reference preview
AirBridge VS-YOFIMN-000
Brand: Vivint Pages: 2

Brands by name

Popular brands

Load more brands