manualshive.com logo in svg

Renesas SH7705, Hardware Manual

The Renesas SH7705 user manual is a comprehensive hardware guide for this powerful product. Download it for free from manualshive.com to explore the device's features, functionalities, and technical specifications. This manual ensures a seamless user experience, enabling you to unlock the full potential of the Renesas SH7705.

Share
Download
background image

Rev. 2.00, 09/03, page 515 of 690

Bit

Bit
Name

Initial
Value

R/W

Description

7 to
0

PF7DT
to
PF0DT

0

R/W

Table 20.6 shows the function of PFDR.

Table 20.6

Port F Data Register (PFDR) Read/Write Operations

PFCR State

PFnMD1

PFnMD0

Pin State

Read

Write

0

0

Other function PFDR value

Data can be written to PFDR but no effect on
pin state.

1

Output

PFDR value

Written data is output from the pin.

1

0

Input (Pull-up
MOS on)

Pin state

Data can be written to PFDR but no effect on
pin state.

1

Input (Pull-up
MOS off)

Pin state

Data can be written to PFDR but no effect on
pin state.

Note:

n = 0 to 7

20.7

Port G

Port G is an 8-bit input port with the pin configuration shown in figure 20.7. Each pin has an input
pull-up MOS, which is controlled by the port G control register (PGCR) in the PFC.

Port G

PTG5 (input/output)/

BACK

 (output)

PTG4 (input/output)/AUDCK (output)
PTG3 (input/output)/

TRST

 (input)

PTG2 (input/output)/TMS (input)
PTG1 (input/output)/TCK (input)
PTG0 (input/output)/TDI (input)

PTG7 (input/output)/

WAIT

 (input)

PTG6 (input/output)/

BREQ

 (input)

Figure 20.7 Port G

20.7.1

Register Description

Port G has the following register. For details on the register address and access size, see section
24, List of Registers.

•

Port G data register (PGDR)

Summary of Contents for SH7705




































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7705

Ruckus Wireless ZoneFlex 7731 Getting Started Manual preview
ZoneFlex 7731
Brand: Ruckus Wireless Pages: 56
Renesas RSKH836079 Quick Start Manual preview
RSKH836079
Brand: Renesas Pages: 6
Usr USR4504 Installation Manual preview
USR4504
Brand: Usr Pages: 2
ROE EVISON HD101 User Manual preview
EVISON HD101
Brand: ROE Pages: 41
FDI ELI70-CR Quick Start Manual preview
ELI70-CR
Brand: FDI Pages: 2
Paradyne Hotwire 8775 MSDSL Installation Instructions Manual preview
Hotwire 8775 MSDSL
Brand: Paradyne Pages: 10
ZoneVu ZSI-450-IP Installation Manual & User Manual preview
ZSI-450-IP
Brand: ZoneVu Pages: 15
FUNcube Dongle Pro User Manual preview
Dongle Pro
Brand: FUNcube Pages: 23
S&T TPMS1209T02-ER User Manual preview
TPMS1209T02-ER
Brand: S&T Pages: 28
GSA Bolide BN-NVR/NX User Manual preview
Bolide BN-NVR/NX
Brand: GSA Pages: 101
Intel SRCU31L Quick Start Manual preview
SRCU31L
Brand: Intel Pages: 20
Garland EdgeSafe M40G1AC User Manual preview
EdgeSafe M40G1AC
Brand: Garland Pages: 159
National Instruments GPIB-ENET-1000 Installation Manual preview
GPIB-ENET-1000
Brand: National Instruments Pages: 35
ADTRAN NetVanta 3430 Manual preview
NetVanta 3430
Brand: ADTRAN Pages: 2
ADTRAN OC-12 Manual preview
OC-12
Brand: ADTRAN Pages: 2
ADTRAN SFP Series Quick Start preview
SFP Series
Brand: ADTRAN Pages: 4
ADTRAN TRACER 4205 Quick Start Manual preview
TRACER 4205
Brand: ADTRAN Pages: 9
AT&T AC8200 Installation Manual preview
AC8200
Brand: AT&T Pages: 16

Brands by name

Popular brands

Load more brands