manualshive.com logo in svg

Renesas SH7705, Hardware Manual

The Renesas SH7705 user manual is a comprehensive hardware guide for this powerful product. Download it for free from manualshive.com to explore the device's features, functionalities, and technical specifications. This manual ensures a seamless user experience, enabling you to unlock the full potential of the Renesas SH7705.

Share
Download
background image

Rev. 2.00, 09/03, page 250 of 690

8.3.6

DMA Extended Resource Selectors 0, 1 (DMARS0, DMARS1)

DMARS is a 16-bit readable/writable register that specifies the DMA transfer request sources
from peripheral modules in each channel. DMARS0 specifies for channels 0 and 1, DMARS1 for
channels 2 and 3. This register can set the transfer request of SCIF0, SCIF2, and USB.

When MID/RID other than the values listed in table 8.2 is set, the operation of this LSI is not
guaranteed. The transfer request from DMARS is valid only when the resource select bits (RS3 to
RS0) has been set to B'1000 for CHCR_0 to CHCR_3. Otherwise, even if DMARS has been set,
transfer request source is not accepted.

•

DMARS0

Bit

Bit
Name

Initial
Value

R/W

Description

15

14

13

12

11

10

C1MID5

C1MID4

C1MID3

C1MID2

C1MID1

C1MID0

0

0

0

0

0

0

R/W

R/W

R/W

R/W

R/W

R/W

Transfer request source module ID5 to ID0 for DMA channel
1 (MID)

See table 8.2.

9

8

C1RID1

C1RID0

0

0

R/W

R/W

Transfer request resource register ID1 to ID0 for DMA
channel 1 (RID)

See table 8.2.

7

6

5

4

3

2

C0MID5

C0MID4

C0MID3

C0MID2

C0MID1

C0MID0

0

0

0

0

0

0

R/W

R/W

R/W

R/W

R/W

R/W

Transfer request source module ID5 to ID0 for DMA channel
0 (MID)

See table 8.2

1

0

C0RID1

C0RID0

0

0

R/W

R/W

Transfer request resource register ID1 to ID0 for DMA
channel 0 (RID)

See table 8.2.

Summary of Contents for SH7705




































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7705

2N OfficeRoute Quick Manual preview
OfficeRoute
Brand: 2N Pages: 11
2N stargate How To Set preview
stargate
Brand: 2N Pages: 5
2N Telekomunikace EasyGate IP Brief Manual preview
EasyGate IP
Brand: 2N Telekomunikace Pages: 24
Oracle Talari E1000 Installation Manual preview
Talari E1000
Brand: Oracle Pages: 24
Renesas Asynchronous SH7145F Application Note preview
Asynchronous SH7145F
Brand: Renesas Pages: 17
Waves MaxxBCL Manual preview
MaxxBCL
Brand: Waves Pages: 41
Hama 00039747 Operating Instruction preview
00039747
Brand: Hama Pages: 6
JETWAY HBJC924R3288DG2NS Series Quick Installation Manual preview
HBJC924R3288DG2NS Series
Brand: JETWAY Pages: 6
QNAP Turbo NAS TVS-71 Series Hardware User Manual preview
Turbo NAS TVS-71 Series
Brand: QNAP Pages: 51
Longshine LCS-8170 User Manual preview
LCS-8170
Brand: Longshine Pages: 35
axing EOC 30-01 Quick Start Manual preview
EOC 30-01
Brand: axing Pages: 4
ICP DAS USA iWSN-200E Quick Start Manual preview
iWSN-200E
Brand: ICP DAS USA Pages: 8
Penguin Edge MVME2500 Quick Start Manual preview
MVME2500
Brand: Penguin Edge Pages: 2
Lucent Technologies CIB40 Installation Manual preview
CIB40
Brand: Lucent Technologies Pages: 7
R.V.R. Elettronica PTX30-UHT Installation, Technical And Maintenance Manual preview
PTX30-UHT
Brand: R.V.R. Elettronica Pages: 171
Multi-Tech RJModem MT5656RJ Developer'S Manual preview
RJModem MT5656RJ
Brand: Multi-Tech Pages: 27
Meridian Meridian 1 Option 11C Mini Technical Reference Manual preview
Meridian 1 Option 11C Mini
Brand: Meridian Pages: 546
Bdcom GP3600-16 Hardware Installation Manual preview
GP3600-16
Brand: Bdcom Pages: 25

Brands by name

Popular brands

Load more brands