manualshive.com logo in svg

Renesas SH7705, Hardware Manual

The Renesas SH7705 user manual is a comprehensive hardware guide for this powerful product. Download it for free from manualshive.com to explore the device's features, functionalities, and technical specifications. This manual ensures a seamless user experience, enabling you to unlock the full potential of the Renesas SH7705.

Share
Download
background image

Rev. 2.00, 09/03, page 175 of 690

Bit

Bit
Name

Initial
Value

R/W

Description

31 to 21

0

R

Reserved

These bits are always read as 0. The write value should
always be 0.

20

19

A2ROW1

A2ROW0

0

0

R/W

R/W

Number of Bits of Row Address for Area 2

Specifies the number of bits of row address for area 2.

00: 11 bits

01: 12 bits

10: 13 bits

11: Setting prohibited

18

0

R

Reserved

This bit is always read as 0. The write value should always be
0.

17

16

A2COL1

A2COL0

0

0

R/W

R/W

Number of Bits of Column Address for Area 2

Specifies the number of bits of column address for area 2.

00: 8 bits

01: 9 bits

10: 10 bits

11: Setting prohibited

15 to 13

0

R

Reserved

These bits are always read as 0. The write value should
always be 0.

12

SLOW

0

R/W

Low-Frequency Mode

Specifies the output timing of command, address, and write
data for SDRAM and the latch timing of read data from
SDRAM. Setting this bit makes the hold time for command,
address, write and read data extended. This mode is suitable
for SDRAM with low-frequency clock.

0: Command, address, and write data for SDRAM is output at

the rising edge of CKIO. Read data from SDRAM is
latched at the rising edge of CKIO.

1: Command, address, and write data for SDRAM is output at

the falling edge of CKIO. Read data from SDRAM is
latched at the falling edge of CKIO.

Summary of Contents for SH7705




































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7705

IBM LS42 - BladeCenter - 7902 Installation Manual preview
LS42 - BladeCenter - 7902
Brand: IBM Pages: 56
IBM ATA 133 Quick Hardware Setup Manual preview
ATA 133
Brand: IBM Pages: 2
IBM BladeCenter Management Module User Manual preview
BladeCenter Management Module
Brand: IBM Pages: 78
IBM 9040-MR9 Manual preview
9040-MR9
Brand: IBM Pages: 110
IBM Remote Supervisor Adapter II User Manual preview
Remote Supervisor Adapter II
Brand: IBM Pages: 132
National Instruments NI-9252 Calibration Procedure preview
NI-9252
Brand: National Instruments Pages: 9
Omega OMB-DAQBOARD-3000 Series User Manual preview
OMB-DAQBOARD-3000 Series
Brand: Omega Pages: 108
Altera DE2-70 User Manual preview
DE2-70
Brand: Altera Pages: 93
ADTRAN NetVanta 6355 PoE Installation Manual preview
NetVanta 6355 PoE
Brand: ADTRAN Pages: 46
Taiwan Commate Computer Inc. S630MA Quick Installation preview
S630MA
Brand: Taiwan Commate Computer Inc. Pages: 29
SIIG ID-P20211-S1 Quick Installation Manual preview
ID-P20211-S1
Brand: SIIG Pages: 20
B-G Instruments DataPlot CB1224 Manual preview
DataPlot CB1224
Brand: B-G Instruments Pages: 4
IndigoVision Compact NVR-AS 4000 User Manual preview
Compact NVR-AS 4000
Brand: IndigoVision Pages: 38
Lattice Semiconductor sysCLOCK ECP5 Usage Manual preview
sysCLOCK ECP5
Brand: Lattice Semiconductor Pages: 43
Paradyne ACCULINK 3161 CSU Quick Reference Manual preview
ACCULINK 3161 CSU
Brand: Paradyne Pages: 19
Kaya Instruments KY-FGK Reference Manual preview
KY-FGK
Brand: Kaya Instruments Pages: 48
Intellinet 720564 Instructions preview
720564
Brand: Intellinet Pages: 2
HMS Anybus AWB3000 Startup Manual preview
Anybus AWB3000
Brand: HMS Pages: 18

Brands by name

Popular brands

Load more brands