manualshive.com logo in svg

Renesas SH7705, Hardware Manual

The Renesas SH7705 user manual is a comprehensive hardware guide for this powerful product. Download it for free from manualshive.com to explore the device's features, functionalities, and technical specifications. This manual ensures a seamless user experience, enabling you to unlock the full potential of the Renesas SH7705.

Share
Download
background image

Rev. 2.00, 09/03, page xv of xlvi

Item

Page

Revisions (See Manual for Details)

22.2.10 Execution Times
Break Register (BETR)

552

Note added

Note:  If the channel B brake condition set to during instruction fetch cycles and any of the 

instructions below perform breaks, BETR is not decremented when the first break occurs. 
The decremented values are listed below.

RTE

DMULS.L Rm,Rn

DMULU.L Rm,Rn

MAC.L @Rm+,@Rn+

MAC.W @Rm+,@Rn+

MUL.L Rm,Rn

AND.B #imm,@(R0,GBR)

OR.B #imm,@(R0,GBR)

TAS.B @Rn

TST.B #imm,@(R0,GBR)

XOR.B #imm,@(R0,GBR)

LDC Rm,SR

LDC Rm,GBR

LDC Rm,VBR

LDC Rm,SSR

LDC Rm,SPC

LDC Rm,R0_BANK

LDC Rm,R1_BANK

LDC Rm,R2_BANK

LDC Rm,R3_BANK

LDC Rm,R4_BANK

LDC Rm,R5_BANK

LDC Rm,R6_BANK

LDC Rm,R7_BANK

4

2

2

2

2

3

3

3

3

3

3

4

4

4

4

4

4

4

4

4

4

4

4

4

Instruction

Value 
Decremented

LDC.L @Rm+,SR

LDC.L @Rm+,GBR

LDC.L @Rm+,VBR

LDC.L @Rm+,SSR

LDC.L @Rm+,SPC

LDC.L @Rm+,R0_BANK

LDC.L @Rm+,R1_BANK

LDC.L @Rm+,R2_BANK

LDC.L @Rm+,R3_BANK

LDC.L @Rm+,R4_BANK

LDC.L @Rm+,R5_BANK

LDC.L @Rm+,R6_BANK

LDC.L @Rm+,R7_BANK

LDC.L @Rn+,MOD

LDC.L @Rn+,RS

LDC.L @Rn+,RE

LDC Rn,MOD

LDC Rn,RS

LDC Rn,RE

BSR label

BSRF Rm

JSR @Rm

6

4

4

4

4

4

4

4

4

4

4

4

4

4

4

4

4

4

4

2

2

2

Instruction

Value 
Decremented

23.2 Input/Output Pins

569

Note

*

added

Note:

*

The pull-up MOS turns on if the pin function

controller (PFC) is used to select other functions (UDI).

23.3.3 Boundary Scan
Register (SDBSR)

570

Description amended

SDBSR is a 385-bit shift register, located on the PAD, for
controlling the input/output pins of this LSI.

23.5.2 Points for Attention

582

Item 7 added under “23.5.2 Points for Attention”

7. The CKIO cock should operate during boundary scan.
The MD[2:0] pin should be set to the clock mode used
during normal operation, and EXTAL and CKIO should be
set within the frequency range specified in the Clock Pulse
Generator (CPG) section.

As during normal operation, the boundary scan test should
be performed after allowing sufficient settling time for the
crystal oscillator, PLL1, and PLL2.

24.1 Register Addresses
(by functional module, in
order of the corresponding
section numbers)

592

Access size of EP1 data register and EP2 data register
amended to 8/32

Summary of Contents for SH7705




































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SH7705

ABB RELION REF615R Manual preview
RELION REF615R
Brand: ABB Pages: 66
Maco Standard Fitting Instructions Manual preview
Standard
Brand: Maco Pages: 38
TC Electronic DB6 User Manual preview
DB6
Brand: TC Electronic Pages: 174
TC Electronic Finalizer Express User Manual preview
Finalizer Express
Brand: TC Electronic Pages: 33
F5 i5000 Series Platform Manual preview
i5000 Series
Brand: F5 Pages: 72
3Com OfficeConnect WX2200 User Manual preview
OfficeConnect WX2200
Brand: 3Com Pages: 204
Lanner NCA-4035 User Manual preview
NCA-4035
Brand: Lanner Pages: 109
Grizzly PSJ-M3 GEN2 User Manual preview
PSJ-M3 GEN2
Brand: Grizzly Pages: 9
Buffalo LinkStation Quick Setup Manual preview
LinkStation
Brand: Buffalo Pages: 2
Uniden Data 2000 Manual preview
Data 2000
Brand: Uniden Pages: 5
Idis DR-1204P Installation Manual preview
DR-1204P
Brand: Idis Pages: 22
Segger J-Link-OB-STM32F072-128KB User Manual preview
J-Link-OB-STM32F072-128KB
Brand: Segger Pages: 18
Seagate CHEETAH ST34501FC Product Manual preview
CHEETAH ST34501FC
Brand: Seagate Pages: 68
Raven RFMOW V2 User Manual preview
RFMOW V2
Brand: Raven Pages: 33
Microtek MiniLink Operation Manual preview
MiniLink
Brand: Microtek Pages: 25
National Semiconductor Data Capture Board CLC-CAPT-PCASM User Manual preview
Data Capture Board CLC-CAPT-PCASM
Brand: National Semiconductor Pages: 15
Flexwatch FW3870 User Manual preview
FW3870
Brand: Flexwatch Pages: 13
Vista VIPER H4 User Manual preview
VIPER H4
Brand: Vista Pages: 93

Brands by name

Popular brands

Load more brands