Polaris 2014 Sportsman 570 EF Service Manual Download Page 399

Page: 399 / 456

10.19

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

SPEED SENSOR

Speed Sensor Location

The speed sensor is located on the RH transmission
case and can be accessed through the rear RH wheel
well area.

NOTE: Image For Reference Only.

Speed Sensor Testing

Special Tools Required:

Static Timing Light Harness (PN 2871745)

Hall Sensor Probe Harness (PN 2460761)

Disconnect the 3 wire harness from the speed
sensor

and

remove

the

sensor

from

the

transmission.

Connect the wires from the Static Timing Light
Harness to the sensor 3 pin connector using the Hall
Sensor Probe Harness (PN 2460761).

Pass a screwdriver back and forth in front of the
sensor tip.

Be sure connections are good and 9V battery is in
good condition. If the light flashes, the sensor is
good.

ELECTRICAL

Summary of Contents for 2014 Sportsman 570 EF


























































































































































































































































































































































































































Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands

Polaris 2014 Sportsman 570 EF, Service Manual

Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands