Polaris 2014 Sportsman 570 EF Service Manual Download Page 364

Page: 364 / 456

9.20

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

FRONT CALIPER

Removal

WARNING

Use care when supporting vehicle so that it does not tip

or fall. Severe injury may occur.

Loosen and remove brake line to caliper. Place a
container under caliper to catch fluid draining from
brake line.

Push upper pad retainer pin inward and slip brake
pads past edge. Loosen pad adjuster.

Remove mounting bracket, pin assembly and dust
boot.

Remove piston, dust seals and piston seals.

Clean the caliper body, piston, and retaining bracket
with brake cleaner or alcohol.

NOTE: Be sure to clean seal grooves in caliper
body.

BRAKES

Summary of Contents for 2014 Sportsman 570 EF


























































































































































































































































































































































































































Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands

Polaris 2014 Sportsman 570 EF, Service Manual

Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands