Polaris 2014 Sportsman 570 EF Service Manual Download Page 391

Page: 391 / 456

10.11

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

Units of Measurement

STANDARD DISPLAY

METRIC DISPLAY

Distance

Miles (MPH)

Kilometers (KM/H)

Time

12-Hour Clock

24-Hour Clock

To change between Standard and Metric units of measurement, follow these steps:

1. Turn the key to the OFF position.

2. Press and hold the MODE button while turning the key to the ON position.

3. When the display flashes the distance setting, tap the MODE button to advance to the desired setting.

4. Press and hold the MODE button to save the setting and advance to the next display option.

5. Repeat the procedure to change remaining display settings.

ELECTRICAL

Summary of Contents for 2014 Sportsman 570 EF


























































































































































































































































































































































































































Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands

Polaris 2014 Sportsman 570 EF, Service Manual

Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands