Polaris 2014 Sportsman 570 EF Service Manual Download Page 415

Page: 415 / 456

10.35

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

Remove O-Ring (D) from headlight pivot pins. (Both
Sides)

Pull the headlight housing up to release from the
locking tabs.

Lift the adjusting knob up to remove from the locking
tabs.

Carefully pull the assembly up and out of pod.

Reverse the steps to install the new housing and
reassemble the pod.

NOTE: The distance from the headlamp parting
line to the end of the adjustment knob stop is 5 1/
8”, (13 cm). See illustration.

Adjust the headlight aim by turning the adjusting
knob.

High Beam Headlight Adjustment

The headlight beam can be adjusted to any position
desired by turning the adjusting knob located on the
bottom right side of the headlight pod.

Raise

Headlight

Turn

knob

counter-

counterclockwise

Lower Headlight - Turn knob clockwise

ELECTRICAL

Summary of Contents for 2014 Sportsman 570 EF


























































































































































































































































































































































































































Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands

Polaris 2014 Sportsman 570 EF, Service Manual

Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands