Polaris 2014 Sportsman 570 EF Service Manual Download Page 47

Page: 47 / 456

2.27

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

Place a suitable drain pan underneath the lower
engine hose(1) on the right-hand side of the vehicle.

Remove the hose and completely drain the engine.
Reinstall the lower coolant hose.

Properly dispose of the coolant.

Remove the pressure cap. Using a funnel, add the
recommended coolant to the top of the filler neck and
fill the recovery bottle to the MAX level.

10. Refer to Chapter 3 for the “Cooling System Bleeding

Procedure”.

Polaris Premium Antifreeze

2871534 - Quart

2871323 - Gallon

Radiator/Grill Screen

Check radiator air passages for restrictions or
damage. Check and clean the radiator grille if
needed.

Carefully straighten any bent radiator fins.

Remove any obstructions with compressed air or low
pressure water.

MAINTENANCE

Summary of Contents for 2014 Sportsman 570 EF


























































































































































































































































































































































































































Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands

Polaris 2014 Sportsman 570 EF, Service Manual

Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands