Polaris 2014 Sportsman 570 EF Service Manual Download Page 198

Page: 198 / 456

5.4

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

Remove the front storage box lid / front rack from the
vehicle.

Reverse procedure for installation.

Footwell Removal / Installation

Remove the plastic inserts(2) that secure the footwell
to the front fenders.

Remove the screws (11) that secure the footwell to
the rear fenders

Remove the screws (5) from the bottom of the foot
well. Remove the footwell.

Reverse the removal procedures to install the foot
well. Be sure to properly align the fender ends into
the foot wells upon reassembly.

BODY / STEERING / SUSPENSION

Summary of Contents for 2014 Sportsman 570 EF


























































































































































































































































































































































































































Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands

Polaris 2014 Sportsman 570 EF, Service Manual

Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands