Polaris 2014 Sportsman 570 EF Service Manual Download Page 274

Page: 274 / 456

6.40

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

Remove nut (C) (left hand thread) from puller rod
and set aside.

Remove adapters from puller.

10. Remove bushing and removal tool from adapters.

Discard bushing.

Clutch Bushing Installation

11. Install puller adapter (Item 10) onto puller.

12. Install adapter (Item 9) onto puller.

13. Apply Loctite® 609 evenly to bushing bore inside

moveable sheave.

14. Install sheave face down on puller.

15. Install new bushing on installation tool (Item 2) and

install assembly into sheave.

16. Install left hand thread nut (C) onto puller rod and

hand tighten against installation tool.

17. Turn clutch sheave counterclockwise, making sure

bushing is drawn straight into bore. Continue until
bushing is seated.

18. Remove nut (C) from puller rod and set aside.

19. Remove installation tool and clutch sheave from

puller.

CLUTCHING

Summary of Contents for 2014 Sportsman 570 EF


























































































































































































































































































































































































































Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands

Polaris 2014 Sportsman 570 EF, Service Manual

Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands