Polaris 2014 Sportsman 570 EF Service Manual Download Page 306

Page: 306 / 456

7.24

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

REAR DRIVE (CV) SHAFT

Inspection

Check the front and rear driveshaft CV boots for any
tears or leaking grease. If the driveshaft boot loses all
grease, CV joint failure will occur.

Removal

Remove rear hub. Refer to “REAR HUB REMOVAL”
in this chapter.

Remove upper carrier bolt. Tip hub outward and
remove shaft from carrier.

Pull

sharply

outward

remove

shaft

from

transmission. Install a new compression ring and
apply an anti-sieze compound to the splines upon
assembly.

Installation

Apply anti-seize compound to splines of shaft.

Install a new lock ring and install the inner shaft.

Slide shaft assembly into the bearing carrier hub.

Lift bearing carrier into place and install bolt to upper
control arm. Torque bolt to specification.

Upper Hub Carrier Bolt:

37 ft-lbs (50 Nm)

FINAL DRIVE

Summary of Contents for 2014 Sportsman 570 EF


























































































































































































































































































































































































































Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands

Polaris 2014 Sportsman 570 EF, Service Manual

Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands